Note: All your User Codes and other custom settings will be erased after performing a factory reset. So that’s how to reset your Schlage FE595, and it should fix the locking issue you’re having with the lock. This step should be completed within 10 seconds. Step 3: Put the battery back in, reconnect it, and then press and hold the Schlage button until it lights green and the lock beeps once.Step 2: Press and release the Schlage button.Step 1: Remove the battery cover and disconnect the battery.To reset your Schlage FE595, follow the steps below: As you probably know, restoring factory default settings is a go-to solution for most problems with Schlage keypad locks. So if the above troubleshooting steps couldn’t fix the issue, perform a factory reset on your lock. You also want to ensure that the batteries are properly installed and reconnect the battery connector properly.Ĭontinue to the next step if the issue persists. Energizer and Duracell are excellent brands to consider. The lock uses 4 AA non-rechargeable alkaline batteries. More so, ensure you get the right batteries and do not mix old batteries with new ones. So, replace the batteries and try to lock your door again to see if it works. Though Schlage FE595 comes with a low battery warning sign (frequent red flashes), you may sometimes not get this signal-probably due to bad batteries. So if the problem persists after trying the first troubleshooting step, check to see if the batteries are in order. Low or completely drained batteries can cause undesirable operations in your lock. But if not, see the next troubleshooting step. So if your lock was actually set to “unlocked”, returning it to the re-lock position will fix the issue. If so, it means “unlocked” is enabled, and you’ll have to rotate the thumb turn to the horizontal position to disable “unlocked” mode. So check the inside assembly of your lock to see if the thumb turn is set to the vertical position. What this means is, your lock will not lock when the “unlocked” feature is enabled. But the reverse is the case when your lock is set to “unlocked” - you won’t need a User Code to unlock it. What is “unlocked” in Schlage FE595, you ask? “Unlocked” is a feature in Schlage FE595 that (when enabled) keeps your lock unlocked until you disable it.Īs you probably know, your lock automatically relocks after unlocking it via the keypad. Check that Your Lock Isn’t Set to Unlocked Schlage FE595 Won’t Lock: How to Troubleshoot 1. Schlage FE595 Won’t Lock: How to Troubleshoot. F or FE575 and FE595, page 5.īattery is dead and MUST be replaced. There is a delay before unlock after a valid User Code is entered.īattery is low and should be replaced. If keypad does not respond after 30 seconds, then replace battery. Too many incorrect User Codes have been entered. See the Keypad Locks Programming Guide to disable Vacation Mode. User Code entered is not a valid User Code. Then add all needed User Codes back into the lock. I need to delete a User Code that I don’t remember.ĭelete all User Codes. Outside thumbturn does not freely spin after deadbolt is thrown. If needed, restore lock to factor y settings. See the Keypad Locks Programming Guide for instructions to enable the Turn Lock feature.Ĭheck front of Keypad Locks Programming Guide or back of keypad assembly for default Programming Code. Ensure the cam and bolt positions are correct, as referenced in the installation instructions.īE365: after pushing Schlage button and rotating thumbturn, the deadbolt does not extend. Your lock has been installed incorrectly and is not secure. I can unlock my deadbolt by simply pushing the Schlage button. Customer Service cannot retrieve lost default codes! Do not restore factory settings unless you can locate the default codes.ġ. All existing User Codes and current Programming Code will be erased. Programming Guide or the back of the keypad before beginning! Default programming and User Codes will be restored. WARNING: Locate the default programming and User Codes on the front of the Keypad Locks
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |